|
A "flying" ridgepole with iron rods -- Is this common?
#6025
12/18/05 01:02 AM
|
Joined: Dec 2005
Posts: 3
Caoimhin
OP
Member
|
OP
Member
Joined: Dec 2005
Posts: 3 |
I've got a 24' x 40' tractor barn built just after the turn of the 20th century. It's a combination timber frame/ stick frame, but here's the weird part: there's no ridgepole, but there are two sets of pseudo-rafters that come up toward the ridge from either side of several of the floor beams (they're not attached to the roof). They meet at a simple 2x8 "ridgepole" that's a few feet below the ridge. Through this ridgepole are fastened two iron rods that dive straight down through the two beams, and there's a large washer and nut on the underside of the beams.
I know little about framing, and am probably not describing this well (I could post a picture or two), but I've never seen this before. It seems original to the structure.
Anyone see this design before, and was it just to keep the floor from sagging?
Thanks!
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6026
12/18/05 12:30 PM
|
Joined: Dec 2005
Posts: 6
Al
Member
|
Member
Joined: Dec 2005
Posts: 6 |
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6027
12/18/05 08:50 PM
|
Joined: Dec 2005
Posts: 3
Caoimhin
OP
Member
|
OP
Member
Joined: Dec 2005
Posts: 3 |
Photos of the barn in question: http://depts.husson.edu/caseyk/barn/ Any help in putting a name to this strategy (principal rafters that meet at a flying ridgepole with vertical iron rods that tie to the beam below) would be appreciated.
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6028
12/19/05 02:58 AM
|
Joined: Jun 2002
Posts: 136
John Buday
Member
|
Member
Joined: Jun 2002
Posts: 136 |
Could you post photos of the "floor beam" to post conection and the rod to floor beam conection?
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6029
12/19/05 04:13 PM
|
Joined: Mar 2002
Posts: 1,688
Jim Rogers
Member
|
Member
Joined: Mar 2002
Posts: 1,688 |
From what I could see, and how it's described, it seems to be some sort of truss to hold up the floor. Maybe?
Whatever you do, have fun doing it!
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6030
12/19/05 07:55 PM
|
Joined: Dec 2005
Posts: 6
Al
Member
|
Member
Joined: Dec 2005
Posts: 6 |
It looks like the simplest of King Post trusses. The rod is acting in tension holding the floor beam up at close to mid span and directing the load to the exterior wall timbers. I haven't seen it used like that before but it sure is a simple solution.
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6031
12/20/05 01:37 AM
|
Joined: Nov 2003
Posts: 1,124
Mark Davidson
Member
|
Member
Joined: Nov 2003
Posts: 1,124 |
was the cieling(second floor) ever used to hold up weight? like an engine hoist? you would probably see marks from the fasteners even if the system is gone....
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6032
12/20/05 02:34 PM
|
Joined: Apr 2002
Posts: 895
daiku
Member
|
Member
Joined: Apr 2002
Posts: 895 |
Interesting. The designer clearly knew better than to hang the king rod from rafters that weren't attached to the tie beam. This scheme allowed him to drop the tie beam. Perhaps to increase the loft space? CB.
-- Clark Bremer Minneapolis Proud Member of the TFG
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6033
12/21/05 11:24 AM
|
Joined: Dec 2005
Posts: 3
Caoimhin
OP
Member
|
OP
Member
Joined: Dec 2005
Posts: 3 |
|
|
|
Re: A "flying" ridgepole with iron rods -- Is this common?
#6034
12/22/05 10:19 PM
|
Joined: Apr 2002
Posts: 49
Joe Miller
Member
|
Member
Joined: Apr 2002
Posts: 49 |
No doubt, from looking through the pictures, that is a simple king "post" truss to support the floor. Doesn't appear to have anything to do with supporting the roof.
So cool.
Joe
|
|
|
|
|
|
|