|
Workshop Design
#11192
04/21/07 06:49 PM
|
Joined: Apr 2007
Posts: 5
Lester
OP
Member
|
OP
Member
Joined: Apr 2007
Posts: 5 |
I am about to design and build a new timberframe workshop. Any ideas on effecient use of space inshop and storage outside would be appreciated.
|
|
|
Re: Workshop Design
[Re: Lester]
#11196
04/22/07 04:25 AM
|
Joined: Nov 2003
Posts: 1,124
Mark Davidson
Member
|
Member
Joined: Nov 2003
Posts: 1,124 |
how much floor space will the workshop be? how much yard space do you have? how will you be handling your timbers?
|
|
|
Re: Workshop Design
[Re: Lester]
#11203
04/22/07 08:42 PM
|
Joined: Jan 2007
Posts: 53
Griffon
Member
|
Member
Joined: Jan 2007
Posts: 53 |
Length: For scarfing roof plates/purlins, think of the longest assembly you wish to produce. If you can't cover all, think of free access to allow the ends to stick out while working on such a joint, along with manoeuvrability to remove/manipulate the finished product.
Time is an ocean but it stops at the shore Bob Dylan
|
|
|
Re: Workshop Design
[Re: Mark Davidson]
#11207
04/23/07 12:57 PM
|
Joined: Apr 2007
Posts: 5
Lester
OP
Member
|
OP
Member
Joined: Apr 2007
Posts: 5 |
I will require a floor space of at least 30' x 50'. The yard is unlimited ( many acres) but topography limits flat ground to about 2 acres. Timbers will be handled by tractor, cart and rollers. Thanks for the thoughts.
|
|
|
Re: Workshop Design
[Re: Griffon]
#11208
04/23/07 01:00 PM
|
Joined: Apr 2007
Posts: 5
Lester
OP
Member
|
OP
Member
Joined: Apr 2007
Posts: 5 |
As far as timber manipulation, I have been using a flow through the shop system (in the front door , out the back door) Any comments on this would be appreciated. Thanks
|
|
|
Re: Workshop Design
[Re: Lester]
#11209
04/23/07 05:00 PM
|
Joined: Jan 2007
Posts: 53
Griffon
Member
|
Member
Joined: Jan 2007
Posts: 53 |
Can't comment further on through-flow manipulation; sounds efficient. Exposition: my workshop is oriented south and open on this side also. There is a generous margin sheltered by the roof. Thus, I get winter sun at low angles, and shade in the summer.
Time is an ocean but it stops at the shore Bob Dylan
|
|
|
Re: Workshop Design
[Re: Griffon]
#11230
04/25/07 10:59 AM
|
Joined: Apr 2007
Posts: 5
Lester
OP
Member
|
OP
Member
Joined: Apr 2007
Posts: 5 |
I like the idea of a generous overhang (or even a roofed area) on the front(infeed side of shop). Possible temporary storage for uncut beams. I am tempted to face the broad side of the shop south due to the timing of my shop use. I am usually onsite during the hotter months. Thanks again for your thoughts from France.
|
|
|
Re: Workshop Design
[Re: Lester]
#11284
04/28/07 01:53 AM
|
Joined: Nov 2003
Posts: 1,124
Mark Davidson
Member
|
Member
Joined: Nov 2003
Posts: 1,124 |
Dealing with the timbers that are not in the shop is always a concern, there is never enough quality space to store those timbers that are not yet cut, or are finished being cut. A local timberworker has a great solution, a six posted storage shed with 10 foot overhangs that houses many timbers out of the weather. Some kind of permanent outside storage is a great advantage.
|
|
|
|
|
|
|